Monday, February 10, 2014

Adjusting Noiseless Portable

The Remington Noiseless Portable required still quite a whack at the keys, my particular specimen needed this to make an even imprint. Hitting the keys without a firm (staccato) wallop, would make an uneven imprint, with the top half of the characters very light or not even there.

This is then of course a case where the carriage and platen sits a bit too low for the type striking the platen, with most of the force on the lower half of the type. Given that the carriage rests on a single, small screw in a lip extending from the frame, it is probably logical to have sagged a bit over time. Having looked at it now for a while, finally grabbed some tools and had a go at adjusting this.

Most amazingly (to me, at least) there are two screws in the RNP to adjust the height of the platen for lowercase and for uppercase. The screws have of course a lock-nut to keep them in place during use. (Haven't quite figured out how a left-right height adjustment is done, but that was fortunately still ok :)


All the tools that were needed, are a small screwdriver and a 1/4" open wrench. Having tried first of course with metric tools, luckily had an Imperial wrench of the right size. (Actually used an Allen key, but also not an allen key...)


Started by making sure the imprint of the lowercase is nicely even. Lowercase has the p and q for the lower and the d and b for the top of the needed imprint, so with a bit of trial and error the lowercase can be adjusted to make an even imprint. Striking several times a letter from firm to very lightly to make an increasingly faint impression gives a good cue to see if the platen is properly centered in front of the type.

The lowercase rests on the screw, so clockwise will raise the platen. The uppercase pulls on the adjustment screw, clockwise will lower the platen.


With the lowercase adjusted, the uppercase will be out of line. So as the next item loosened the lock-nut. A small wrench can just squeeze in to loosen the uppercase lock-nut, parallel-beak pliers that can work on the lowercase just couldn't get there.


Result now is a Noiseless Portable that is much less critical about the typing force with a more even result on paper.

(Still needs staccato typing, the letter a is particularly sensitive. Must be another adjustment somewhere on the machine for that :-)

9 comments:

  1. This is a useful reference. Thanks for posting.

    ReplyDelete
  2. Very beautifully presented information.

    ReplyDelete
  3. Good stuff, thanks for the clarity. I have three (maybe four) machines like this and though the height adjustment seems fine, a couple can only make faint-ish impressions. I'd put it down to platen shrinkage but I'm wondering now if there's a tweak to bring the platen forward - otherwise I'm resigned to using a thick backing sheet.

    ReplyDelete
  4. Tnx, s fun to tinker and improve a machine just a little :-)
    You made me curious Rob. Looking again I do think the carriage rail is really fixed in place onto the inner frame. Alignment seems to be manufactured into the parts (a bit harder for the metalware shop, but very good for low cost assembly).

    (Your 'maybe four' has me rather intrigued...)

    ReplyDelete
  5. I seem to recall that 30 or 40 years ago, you could buy a special ribbon for a noiseless. I always thought they just had extra ink, but perhaps they had heavier fabric? Before nylon ribbons, you could often see the fabric threads in the type impression.

    ReplyDelete
    Replies
    1. Maybe it did, the ribbon being pushed instead of whacked. Noiseless machines also needed a very non-standard spool, only a hub really and no spool at all.
      Not sure how aggressive the RNP is on ribbon, but it indeed does vary. Tried silk ribbon briefly in my Corona Speedline and it pretty much tore it to shreds, really needed stronger fabric.

      Delete
  6. So to be clear. To adjust uppercase I loosen the nut to turn the screw? Is that what I do?

    ReplyDelete
    Replies
    1. Yep. The nut is only to lock the screw. The screw is the adjustment. Best of luck!

      Delete
    2. I have the right screwdriver, but grrr I have to get a small 1/4 open wrench for that nut. And then the idea is to hold the nut while tightening the screw clockwise? Mu upper case is currently (nearly) a line above my lowercase on the RDN

      Delete